How to do fixture installation? Lighting installation notes

Good Home Decorative Lighting not only brings light to the night, but also creates a warm and comfortable home environment. The lighting experience of a living room is not only the quality of the lighting, but also closely related to the installation of the lighting . Lighting installation is not a simple matter, but also requires some skills. So, how do fixtures work in the end?

Lighting installation, preparation

First of all, we have to prepare for construction. The architectural structures related to the installation of Lamps and Lanterns shall comply with the relevant provisions of the acceptance specification of the construction project. Formwork and scaffolds that interfere with the installation of the lamps and lanterns in the construction project must be dismantled. Ground cleaning is completed and the door can be closed. Do a good job with the civil construction to do the pre-embedded work, install the lamp's wiring port has been repaired, and measure the line. During the operation, familiarize yourself with the drawings first, and make material plans according to the design and installation drawings. All aspects meet their design requirements; then check the lamps. Various properties of the lamps and lanterns must meet the design requirements and national standards. Manufacturers must provide lamp assembly and installation instructions. Certification.


Lighting installation II, check the lamps

Lighting Accessories without mechanical damage. The wiring inside the lamp is well-insulated and there is no leakage. The place where the conductor branch of the light box is connected cannot have extra profit and wear. The conductors must be insulated and not too close to the heat source. The wiring must not be exposed. Wire the wiring correctly according to the wiring diagram provided by the manufacturer.



Lighting installation three, installation precautions

1. It is forbidden to use wood to install the lighting device and use the embedded terminal box, screw, hook, expansion bolt or plastic plug to fix it.

2. Fireproof and heat insulation measures must be taken around the lamps, and cold light sources should be used as much as possible.

3. In the lighting device installed on the insulation table, the insulated portion of the wire joint needs to be on the surface of the insulation table.

5, safety issues must be noted that the installation of a relatively large light fixtures, scaffolding must be set up to operate, and the giant lights of large sites to prevent its fragmentation after the splash of the measures, the top of the ladder to be fastened, for the smooth ground, it must To consider anti-skid measures, it is best to wear a seatbelt for work at height, and fire prevention measures must be taken to work in the ceiling room.



Lighting installation four, lighting installation errors

1, too many home spotlights

Some customers, because of the limited funds for renovation, hope to make up for various imperfections in their homes through lighting in the later period. Among them, installing too many spotlights is the most common. As a result, it has been found that too many spotlights not only waste electricity, but also are uncomfortably hot.

In fact, installing too many spot light sources is an inappropriate choice. Let us not discuss the power consumption of spotlights. In terms of safety hazards, too many spotlights generate a lot of heat, and home improvement products have been exposed to high temperatures for a long time, which is more likely to lead to fires.



2, the table chandelier is not coordinated

In addition to style, style, many people's home restaurant will appear on the table and the lamps are not in the same center, the table did not move, the lights can not move fixed. Therefore, when selecting a chandelier, it is necessary to consider the style of the home, the layout of the furniture, and the installation of the luminaire. It is recommended to select a large piece of furniture first, and then select the luminaire after the size is determined.



3, aisle did not install lamps

The absence of lighting fixtures on the aisle is a common problem in many households. The aisle is the transition between the living room and each room. Generally, the lighting is poor. Installing the lamps in the aisle properly not only facilitates daily life, but also makes the aisle appear spacious.



4, bedroom did not install sub-control

Some customers did not consider it well before the renovation. The bedroom kept only one switch. It was difficult to find the switch when it was dark at night. The faction reminds parents that during the renovation period, practicality is important, in addition to aesthetic considerations. Sub-controls are installed next to the door and on the bedside to facilitate everyday life, especially for the elderly and children.

The luminaire is a beautiful and practical household article. Since the luminaire is installed at the top and involves electricity, it is very important to ensure the safety. The installation of the luminaire is the most crucial part. You must not neglect it!

Lamps and lanterns installation bathroom door